Muchmore Racing









HOME > Support
     
FLETA USB Link V1.3 PC program (ENG)
FLETA PRO ESC
File DownLoad : MuchmoreRacing_FLETA_USB_Link_V1.3.zip   
New FLETA ESC V1.3 Firmware improved information 

Expert V1.3 
*Power level value 1 to 12 (Last firmware V1.2 1 to 9)
ex)  Last firmware V1.2 Power level set 1 = V1.3  Power level set 4
Provides more smoother throttle punch.
*Add "Max RPM" (You can check max motor RPM)

Stock V1.3 
*Power level value 1 to 12 (Last firmware V1.2 1 to 9)
ex)  Last firmware V1.2 Power level set 1 = V1.3  Power level set 4
Provides more smoother throttle punch.
*Add "Max RPM" (You can check max motor RPM)

Blinky V1.3
*Power level value 1 to 12 (Last firmware V1.2 1 to 9)
*More linear power band
*More fast LED blinking
*When you turn on the power, you can simply check LED blinking without TX( Radio).
*Add "Max RPM" (You can check max motor RPM)


20140702_174240.jpg
 


1. Download  Muchmore Racing FLETA USB Link V1.3 PC program.  
Unzip the file and install SETUP file.
 
01.jpg
  
2. Click 'Next' button
 
 
02.jpg
 
3. Remember the installed file. Exist 'USB driver installation program' in this folder.
   Click 'Next' button
 
 
03.jpg
 
4. Click 'Install' button
  
5. Installing  'FLETA USB Link V1.3 program in the PC'. 
 
04.jpg
 
6. Installed 'Muchmore Racing FELTA USB Link V1.3 program in the PC'.
 
 
15.jpg
 

 
7. If you cannot install to pc. Check the compatibility.
 
 
 
8. Move the folder installed the program,  
(c:/..../Muchmore Racing FLETA USB Link V1.3/driver/)
run  'CP210xVCPInstaller.exe ' and install USB driver installation file.
(In case of existing USB driver, do not need to install )
 
16.jpg
 

 
9. Click the icon of 'Muchmore Racing FLETA USB Link V1.3' and run this program. 
 
 
01.jpg
 

 
10. This is the First page of  'Muchmore Racing FLETA USB Link V1.3'.
Click right available products and then move to the introduce page of each item.
 
 
[ FLETA USB Link V1.3 How to used ]
 
 
11. Do not forget to disconnect the battery with connector when the PC connect the program card certainly.
Please pay attention of this point specially, connect +, - has been causing huge damages.
 
Currents are flowing through the USB port, please do pay attention.
 
 
02.jpg
 

 
12.Once the card is connected to the program, 'USB' connection is turned on.
 
 
03.jpg
 

 
13. The person who first used the firmware, please firmware update firstly. 
     Without the firmware program, it does not operate normally. 
 
     Check ;
     Top Menu > Device > Program Card
     In case of the connecting, mark 'ON' - ' Program Card Connected '
     If not, please check your cable connecting firmly.
 
 
04.jpg
 
 
14. Move the 'FIRMWARE MENU'
Choose the FLETA SHR V 1.30 in the Change Firmware, click the 'PROGAM CARD FIRMWARE SAVE' button.
Please wait until finishing the text of ready box in the bottom part (running 1~100% and pop the finish text).
Do not remove the connector during update the firmware, this may cause the equipment failure.
 
 
13.jpg
 
 
15. Confirm the V1.30 in the program card.
 
 
05.jpg
 

 
16. Top Menu > Device > ESC
Choose the firmware from the change Firmware, click the ' ESC FIRMWARE SAVE' button.
Please wait until finishing the text  of ready box in the bottom part (running 1~100% and pop the finish text).
Do not remove the connector during update the firmware, this may cause the equipment failure.
 
 
06.jpg
 

 
17. Not available to use the menu 'TECHNICAL SETUP' menu on Blinky firmware.
Also do not show the menu 'TECHNICAL SETUP' in a program card.
 
 
07.jpg
 

 
18. FLETA USB V1.3 supply the preset profile of Factory drivers.
Choose the applying class from the category menu.
 
 
08.jpg
 

 
19. Available to load Basic profile and Factory drivers' setup data from each category.
 
 
09.jpg
 

 
20. When you select the profile,  set-up data is applied, and team driver setup comment is shown in the right.
Information is shown real race data of drivers.
 
Profile will be continuously updated.
 
 
10.jpg
 

 
21. Correct the setup data and click 'SEND SETTING' button.
Please wait until finishing the text  of ready box in the bottom part (running 1~100% and pop the finish text).
Do not remove the connector during update the firmware, this may cause the equipment failure.
 
 
11.jpg
 

 
22. Top Menu > File > Export Settings
     Save the SETUP data.
 
 
12.jpg
 

 
23. Top Menu > File > Import Settings
     Load the saving SETUP data.


When you changed to ESC firmware, you must default reset.

14.jpg
 

 

SUPPORT LIST